Honeywell 05701-A-0361

我们这里有您急需的停产备件，

优势现货，询不到的，买不到的，请联系我们！

欢迎来电询价，我们将会给您满意的价格！

公司主营进口PLC模块，可编程控制器，伺服控制系统，和DCS备件等，
例如：ABB、AB、GE， Bently，FOXBORO. MOTOROLA. XYCOM.HONEYWELL.YASKAWA. SIEMENS. SCHNEIDER. REXROTH. YOKOGAWA .KUKA .OVATION .OMRON 等。
尊敬的顾客您好，为了更好的保障您的合法权益，购买前请仔细阅读以下内容：

1.由于市场波动频繁，本店所标价格，并非实价，请买家提前咨询后再拍，感谢支持！

2，本店所售商品均为正品现货，图片实物拍摄。分为全新原装、全新无包装，工程余货和二手四种货品。购买前请联系客服仔细核对货品、型号、数量。

3， 本店所售商品保证质量，全新无包装和二手商品签收三日质量出现问题均包退换，请放心购买。因买家自己弄错产品型号、参数或剪脚、上机、错误接入电源、错误安装、保管不当、人为损坏等除外。

4，本店所售商品国内顺丰包邮，国外运费自理。支持七天内有任何产品质量问题退换货，过期一切损失请自行承担。签收快件前，请先检查包裹内货物是否有：破损、缺少、货物型号和数量不对等，有问题请拒绝签收并及时与我们联系。签收后，一切损失请自行承担。

5,价格说明 并非原价，以询价为准。

In the injection molding machine, the most widely used control law is proportional, integral, differential control, referred to as PID control. When the actual parameters of the pressure, speed and temperature of the injection molding machine can not be completely and reliably mastered, or the accurate mathematical model can not be obtained, and other technologies of the control theory are difficult to adopt, the parameters must be determined by experience and on-site debugging. At this time, the application of PID control technology is the most convenient. That is, when we do not fully understand the actual injection pressure, speed, temperature, or can not obtain the above parameters through effective measurement means, the most suitable PID control technology. PID control, there are also PI and PD control in practice. PID control is based on the error of the system, using proportional, integral and differential to calculate the control quantity.

Proportional control is the simplest control method. The output of the controller is proportional to the input error signal. When there is only proportional control, the system output has steady-state error.

In the integral control, the output of the control system is proportional to the integral of the input error signal. For a control system of injection molding machine, if there is steady-state error after entering steady state, it is said that the control system has steady-state error or system with steady-state error for short. In order to eliminate the steady-state error, "integral term" must be introduced into the pressure, speed and temperature control of injection molding machine. The error of the integral term depends on the integral of time. With the increase of time, the integral term will increase. In this way, even if the error is very small, the integral term will increase with the increase of time, which will promote the output of the injection molding machine computer to increase, and further reduce the steady-state error until it is equal to zero. Therefore, the proportional integral (PI) control can make the injection molding machine system into steady state without steady-state error.

In the injection molding machine, the most widely used control law is proportional, integral, differential control, referred to as PID control. When the actual parameters of the pressure, speed and temperature of the injection molding machine can not be completely and reliably mastered, or the accurate mathematical model can not be obtained, and other technologies of the control theory are difficult to adopt, the parameters must be determined by experience and on-site debugging. At this time, the application of PID control technology is the most convenient. That is, when we do not fully understand the actual injection pressure, speed, temperature, or can not obtain the above parameters through effective measurement means, the most suitable PID control technology. PID control, there are also PI and PD control in practice. PID control is based on the error of the system, using proportional, integral and differential to calculate the control quantity.

Proportional control is the simplest control method. The output of the controller is proportional to the input error signal. When there is only proportional control, the system output has steady-state error.

In the integral control, the output of the control system is proportional to the integral of the input error signal. For a control system of injection molding machine, if there is steady-state error after entering steady state, it is said that the control system has steady-state error or system with steady-state error for short. In order to eliminate the steady-state error, "integral term" must be introduced into the pressure, speed and temperature control of injection molding machine. The error of the integral term depends on the integral of time. With the increase of time, the integral term will increase. In this way, even if the error is very small, the integral term will increase with the increase of time, which will promote the output of the injection molding machine computer to increase, and further reduce the steady-state error until it is equal to zero. Therefore, the proportional integral (PI) control can make the injection molding machine system into steady state without steady-state error.