F3237(Z7108)

【主营产品】prefix = "o" ns = "urn:schemas-microsoft-com:office:office"

主营：世界知名品牌的PLC、DCS系统备件 模块

①Allen-Bradley(美国AB)系列产品》

②Schneider(施耐德电气)系列产品》

③General electric(通用电气)系列产品》

④Westinghouse（美国西屋）系列产品》

⑤SIEMENS(西门子系列产品)》

⑥销售ABB Robots. FANUC Robots、YASKAWA Robots、KUKA Robots、

Mitsubishi Robots、OTC Robots、Panasonic Robots、MOTOMAN

Robots。

⑦estinghouse（西屋）： OVATION系统、WDPF系统、MAX1000系统备件

。

⑧Invensys Foxboro（福克斯波罗）：I/A Series系统，FBM（现场输入

/输出模块）顺序控制、梯形 逻辑控制、事故追忆处理、数模转换、输入/

输出信号处理、数据通信及处理等。Invensys Triconex: 冗余容错控制

系统、基于三重模件冗余（TMR）结构的zui现代化的容错控制器。

⑨Siemens(西门子)：Siemens MOORE， Siemens Simatic C1，Siemens

数控系统等。

⑩Bosch Rexroth（博世力士乐）：Indramat，I/O模块,PLC控制器,驱动

模块等。

◆Motorola（摩托罗拉）：MVME 162、MVME 167、MVME1772、MVME177等系列。

尊敬的顾客您好，为了更好的保障您的合法权益，购买前请仔细阅读以下内容：

1.价格说明 并非原价，请以询价为准。
  价格说明 并非原价，请以询价为准。

价格说明 并非原价，请以询价为准。

2.由于市场波动频繁，本店所标价格，并非实价，请买家提前咨询      后再拍，感谢支持。

3.所售商品报价均为不含税价 ，如须开票，请和店主联系。

4.本店所售商品均为正品现货，图片实物拍摄。如果您订购产品超过 多件，请与我们联系，我们可以为您尽量提供折扣。

5本店产品分为全新原装、全新无包装，工程余货和二手四种货品。购买前请联系客服仔细核对货品、型号、数量。
6.本店所售商品保证质量，全新无包装和二手商品签收十五日出现问题均包退换，请放心购买。所有配件质保一年。因买家自己弄错产品型号、参数或剪脚、上机、错误接入电源、错误安装、保管不当、人为损坏等除外。
7.本店所售商品国内顺丰包邮，国外运费自理。支持十五天内有任何产品质量问题退换货，过期一切损失请自行承担。请大家在货物签收时一定仔细检查物品外观是否完好无损，数量是否短缺，配件是否齐全如发现有任何问题请不要签收并立即致电我们，货物一旦签收完毕，就代表双方对货物外表、数量、配件一致认可无争议。

拍下商品后,视为认可以上各项条款，谢谢合作！

High speed product positioning is crucial to the success of printing. In order to achieve high-speed positioning, it is necessary to provide high-speed position locking input to the driver or motion controller, so as to capture the accurate spindle position when encountering the positioning mark. The difference between the front and back positions is used to calculate the actual distance between the positioning marks. That is, the distance is compared with the theoretical distance between the marks, and a correction amount is calculated. Then, the correction amount is substituted into the slave axis motion curve.

The time required from the detection of the positioning mark to the application of the correction amount is very important for the production of high quality products. This time is entirely dependent on the motion controller used for the application, and may also be affected by the technology used (for example, some digital motion control networks have a transport lag that must be compensated, which may not be acceptable in some applications). In some applications, it is necessary to use a special positioning algorithm, such as averaging the correction of several or many products, filtering the correction, or not applying the correction in some segments of the motion curve. The motion controller shall also be able to properly handle web splicing and missing positioning marks.

A typical 10 color printing line with basic configuration has more than 65 closed-loop motion control axes. In larger lines, there are usually more than 100 shafts. In the past, each axis was mechanically driven. Now, the updated control system improves the positioning performance and reduces the positioning accuracy to half of the old system. These control systems have high flexibility, can deal with special tasks, and provide unlimited variable repetition. Instead of the speed matching method discussed above, it enables the user to increase or decrease the speed of the plate roller relative to the web to change the repetition length.

These improvements can also make the speed faster, the maximum speed can be increased from 1200 FPM to 2000 FPM, flexographic printing process can achieve higher speed. The average time for a printer to switch from one task to the next is reduced from 4-6 hours to 30 minutes, or even less in some cases. The manipulator with motion control and printing driving device positioning system has a great influence on the switching time. In the application, because the whole control system provides better diagnostic information, the machine production time can be extended.