欢迎您访问:瑞昌明盛自动化设备有限公司,我司将竭诚为您服务!
MOOG D661-5625C伺服控制模块备件江西瑞昌

主页 > 产品中心 > RELIANCE

MOOG D661-5625C伺服控制模块备件江西瑞昌

类目:RELIANCE
型号:D661-5625C
全国服务热线:15270269218
手机:15270269218
微信:15270269218
QQ:3136378118
Email:3136378118@qq.com

在线咨询
产品详情

MOOG  D661-5625C伺服控制模块备件江西瑞昌 MOOG  D661-5625C伺服控制模块备件江西瑞昌 MOOG  D661-5625C伺服控制模块备件江西瑞昌
瑞昌明盛进出口贸易有限公司
主营DCS控制系统备件,PLC系统备件及机器人系统备件,
优势品牌:Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件
MOOG  D661-5625C伺服控制模块备件江西瑞昌 MOOG  D661-5625C伺服控制模块备件江西瑞昌 MOOG  D661-5625C伺服控制模块备件江西瑞昌
构成温差闭环自动控制系统,自动调节水泵的输出流量,为了达到节能目的提供了可靠的技术条件。如图四所示:  
图片加载中…
2.6系统主电路的控制设计 根据具体情况,同时考虑到成本控制,原有的电器设备尽可能的利用。冷冻水泵及冷却水泵均采用一用一备的方式运行,因备用泵转换时间与空调主机转换时间一致,均为一个月转换一次,切换频率不高,决定将冷冻水泵和冷却水泵电机的主备切换控制利用原有电器设备,通过接触器、启停按钮、转换开关进行电气和机械互锁。确保每台水泵只能由一台变频器拖动,避免两台变频器同时拖动同一台水泵造成交流短路事故;并且每台变频器任何时间只能拖动一台水泵,以免一台变频器同时拖动两台水泵而过载。 2.7系统功能控制方式 上位机监控系统主要通过人机界面完成对工艺参数的检测、各机组的协调控制以及数据的处理、分析等任务,下位机PLC主要完成数据采集,现场设备的控制及连锁等功能。具体工作流程:开机:开启冷水及冷却水泵,由PLC控制冷水及冷却水泵的启停,由冷水及冷却水泵的接触器向制冷机发出联锁信号,开启制冷机,由变频器、温度传感器、温度模块组成的温差闭环控制电路对水泵进行调速以控制工作流量,同时PLC控制冷却塔根据温度传感器信号自动选择开启台数。当过滤网前后压差超出设定值时,PLC发出过滤堵塞报警信号。送风机转速的快慢是由回风温度与系统设定值相比较后,用PID方式控制变频器,从而调节风机的转速,达到调节回风温度的目的。停机:关闭制冷机,冷水及冷却水泵以及冷却塔延时十五分钟后自动关闭。保护:由压力传感器控制冷水及冷却水的缺水保护,压力偏低时自动开启补水泵补水。 2.8介绍系统节能改造原理
图片加载中…
1、对冷冻泵进行变频改造控制原理说明如下:PLC控制器通过温度模块及温度传感器将冷冻机的回水温度和出水温度读入控制器内存,并计算出温差值;然后根据冷冻机的回水与出水的温差值来控制变频器的转速,调节出水的流量,控制热交换的速度;温差大,说明室内温度高系统负荷大,应提高冷冻泵的转速,加快冷冻水的循环速度和流量,加快热交换的速度;反之温差小,则说明室内温度低,系统负荷小,可降低冷冻泵的转速,减缓冷冻水的循环速度和流量,减缓热交换的速度以节约电能;and output after voting. In the design of the project, the dual input mode is adopted. A field input signal is distributed to two independent input modules ic660bbd020 through the terminal block, and each module is connected to a separate genius bus belden9182.

2. Configuration of output subsystem

The GE GMR output subsystem includes four modules "H", two module "I" and two module "T" module group configuration. According to the project cost and project scale, the configuration of the output subsystem can be selected. The output module group votes on the output from the CPU and outputs the voting result to the load. Based on the reliability and availability of all equipment, the "t" output configuration is adopted. Each field output is connected by two source modules ic660brd020 at one end of the load, and the other end of the load is grounded. This structure is both fail safe and fault tolerant. The configuration is shown in the figure below.

3. Genius bus belden9182

In the configuration of the whole system, there are two genius buses belden9182 running through