欢迎您访问:瑞昌明盛自动化设备有限公司,我司将竭诚为您服务!
HONEYWELL 51400910-100串行链路控制器

主页 > 产品中心 > RELIANCE

HONEYWELL 51400910-100串行链路控制器

类目:RELIANCE
型号:51400910-100
全国服务热线:15270269218
手机:15270269218
微信:15270269218
QQ:3136378118
Email:3136378118@qq.com

在线咨询
产品详情
瑞昌明盛进出口贸易有限公司
主营DCS控制系统备件,PLC系统备件及机器人系统备件,
优势品牌:Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等。

HONEYWELL 51400910-100串行链路控制器 HONEYWELL 51400910-100串行链路控制器 HONEYWELL 51400910-100串行链路控制器 HONEYWELL 51400910-100串行链路控制器 HONEYWELL 51400910-100串行链路控制器
工业以太网交换机符合IEC61850-3标准,可适应严苛的电力应用环境;
骨干环网采用三层工业以太网交换机,1000M光纤自愈环网。通过启用路由协议,既实现各VLAN数据转发,又保证了当环路某段链路或交换机故障时,快速自愈;
接入环网采用二层工业以太网交换机,100M光纤自愈环网,当环路上光纤或者节点出现故障时,网络可以在15ms快速自愈;
每个接入环划分一个VLAN,可隔离广播,多播包,防止网络风暴蔓延;
网管软件可以实现交换机的集中配置、管理和监控。
如上图所示,本系统基于光纤网,采用IEEE802.3体系标准,采用站控层-间隔层-过程层组网模式,具体情况如下:
配网监控中心:
配网监控中心设备连接图:
监控中心配置MS6028-2G千兆三层交换机一台、网管一套、网管控制台一套。
MS6028-2G负责汇集监控中心的网络设备和N个变电站设备的的接入,并负责对这些数据包进行转发、交换等处理;
网管控制台负责进行网络的参数设置和对网络运行情况进行监控;
变电站:
变电站设备连接图:
变电站配置MS6028-2G-2SC千兆三层交换机一台、网管一套、网管控制台一套。
MS6028-2G-2SC负责汇集变电站的网络设备和N个配电房设备的的接入,以及和监控中心千兆环网的接入。并负责对这些数据包进行转发、交换等处理;
网管控制台负责进行网络的参数设置和对网络运行情况进行监控;
配电房:
配电房配置MS6026-2SC一台。At the same time, it should be noted that lm3310a and lm3310b belong to single ended input. If the negative ends of multiple transmitters cannot be short circuited, only one transmitter can be connected at most, or lm3310 module can be selected. The specific differences between the three are shown in the table below:



3. Lm3320 module is used for analog output, but if you only want to output 0 ~ 5V, can it be realized? A: Yes. Lm3320 can realize 0 ~ 20mA or 0 ~ 10V output. If you only want to output 0 ~ 5V, it can be realized. 4. The standard signal sent by the load cell through the transmitter can be voltage or current signal. Is there any requirement for lm3310? How is the value of this signal reflected in the PLC register? Answer: lm3310 can receive 4 signals of voltage (0 ~ 10V), current (0 ~ 20mA) or current (4 ~ 20mA). Moreover, each signal can be different. Just configure the corresponding signal during PLC configuration. The corresponding relationship is as follows: