欢迎您访问:瑞昌明盛自动化设备有限公司,我司将竭诚为您服务!
BENTLY 3500/44M模块卡件

主页 > 产品中心 > RELIANCE

BENTLY 3500/44M模块卡件

类目:RELIANCE
型号:3500/44M
全国服务热线:15270269218
手机:15270269218
微信:15270269218
QQ:3136378118
Email:3136378118@qq.com

在线咨询
产品详情
瑞昌明盛进出口贸易有限公司
主营DCS控制系统备件,PLC系统备件及机器人系统备件,
优势品牌:Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件
BENTLY  3500/44M模块卡件 BENTLY  3500/44M模块卡件 BENTLY  3500/44M模块卡件

BENTLY  3500/44M模块卡件 BENTLY  3500/44M模块卡件

BENTLY  3500/44M模块卡件
连接在RS485总线上的其它设备产生的瞬态过电压或过电流同样会流入到PLC,总线上连接的设备站点数越多,产生瞬态过电压的因素也越多。
当通信线路较长或有室外架空线时,雷电必然会在线路上造成过电压,其能量往往是巨大的,常有用户沮丧地说:“联网的几十台PLC全部遭打坏了!”。
三、 解决办法:
1、从PLC内部考虑:
●采用隔离的DC/DC将24V电源和5V电源隔离,我们分析了三菱、欧姆龙、施耐德PLC以及西门子的PROFIBUS接口均是如此。
●选用带静电保护、过热保护、输入失效保护等保护措施完善的高挡次RS485芯片,如:SN65HVD1176D、MAX3468ESA等,这些芯片价格一般在十几元至几十元,而SN75176的价格仅为1.5元。
●采用响应速度更快、承受瞬态功率更大的新型保护器件TVS或BL浪涌吸收器,如P6KE6.8CA的钳制电压为6.8V,承受瞬态功率为500W,BL器件则可抗击4000A以上大电流冲击。
●R1和R2采用正温度系数的自恢复保险PTC,如JK60-010,正常情况下的电阻值为5欧,并不影响正常通信,当受到浪涌冲击时,大电流流过PTC和保护器件TVS(或BL),PTC的电阻值将骤然增大,使浪涌电流迅速减小。
2、从PLC外部考虑:
● 使用隔离的PC/PPI电缆,尽量不用廉价的非隔离电缆(特别是在工业现场)。西门子公司早期出产的PC/PPI电缆(6ES7 901-3BF00-0XA0)是不隔离的,现在也改成隔离的电缆了!
● PLC的RS485口联网时采用隔离的总线连接器,如PFB-G,速率为0~1.5Mbps自动适应,外形和使用方法与西门子非隔离的总线连接相同。
● 与PLC联网的第三方设备,如变频器、触摸屏等的RS485口均使用RS485隔离器BH-485G进行隔离,这样各RS485节点之间就无“电”的联系,也无地线环流产生,即使某个节点损坏也不会连带其它节点损坏。
● RS485通信线采用PROFIBUS总线专用屏蔽电缆,保证屏蔽层接到每台设备的外壳并后接大地。
● 对于有架空线的系统,总线上好设置专门的防雷击设施。of wrapping speed. Therefore, we need to increase the amount of film compensation with different wrapping speeds.

The bottle splitting and bottle splitting control in the film wrapping machine has always been a problem that can not be ignored. The bottle splitting of the bottle splitting device will directly affect the wrapping speed behind, thus affecting the speed of the whole production line. At present, there are two kinds of mechanisms used in the bottle separating device. One is to use two motor shafts to keep a fast and slow synchronous relationship with the main motor; The other is to use the pressing plate, baffle and bottle feeding motor shaft to start and stop according to the phase of the main motor. The bottle separation device of the second mode prevents the bottle pouring phenomenon and improves the bottle separation speed. In addition to film feeding and bottle separation, the inlet bottle inlet and hot channel bottle outlet can not reduce the control requirements. The inlet and hot